產品說明0
※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
Sparkfun原廠 MyoWare 2.0 Arduino Shield (DEV-18426) 肌肉配件：擴展板
影片：https://youtu.be/d1oUHqPa35I
The MyoWare® 2.0 Arduino Shield is designed to easily connect up to six MyoWare 2.0 Muscle Sensors and Link Shields using 3.5mm TRS-to-TRS audio cables. The board comes pre-populated with male headers so all you would need to do is stack it on your Arduino and connect the sensors to read up to six muscle groups!
MyoWare® 2.0 Arduino Shield 旨在使用 3.5 毫米 TRS-to-TRS 音頻電纜輕鬆連接多達六個 MyoWare 2.0 肌肉傳感器和 Link Shield。 該板預先裝有公頭，因此您只需將其堆疊在您的 Arduino 上並連接傳感器以讀取多達六個肌肉群！
The Arduino shield form-factor mates directly with development boards that have the Arduino Uno R3 standard footprint. All six analog input pins (A0-A5) on the Arduino are reserved on this shield. Included on the back of the Arduino shield is a power jumper to select your output voltage to be 5V (default) or 3.3V for the muscle sensors. You'll need a MyoWare 2.0 Link Shield and TRS-to-TRS cable for each MyoWare 2.0 Muscle Sensor.
每Arduino shield 外形尺寸直接與具有 Arduino Uno R3 標準封裝的開發板匹配。 Arduino 上的所有六個模擬輸入引腳 (A0-A5) 都保留在此擴展板上。 Arduino 擴展板背麵包含一個電源跳線，用於選擇肌肉傳感器的輸出電壓為 5V（默認）或 3.3V。 每個 MyoWare 2.0 肌肉傳感器都需要一個 MyoWare 2.0 Link Shield 和 TRS-to-TRS 電纜。！
Note: Note: MyoWare and the Arduino Shield are not intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation treatment, or prevention of disease, in a man or other animals. 注意： MyoWare 和 Arduino Shield 不適用於診斷人類或其他動物的疾病或其他狀況，或用於治愈、緩解治療或預防疾病。
The MyoWare® 2.0 ecosystem consists of shields that easily interface with the MyoWare® 2.0 Muscle Sensor, which is a low-cost, Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies. The innovative connector system allows users to easily snap shields together with a compact low profile and connect to a microcontroller's analog input to measure raw, filtered, and rectified electrical activity of a target muscle. This eliminates the need to solder connections between boards.
MyoWare® 2.0 生態系統由可輕鬆與 MyoWare® 2.0 肌肉傳感器接口的防護板組成，這是一款來自 Advancer Technologies 的低成本、與 Arduino 兼容的一體化肌電圖 (EMG) 傳感器。創新的連接器系統使用戶可以輕鬆地將防護罩與緊湊的薄型連接在一起，並連接到微控制器的模擬輸入，以測量目標肌肉的原始、濾波和整流電活動。這消除了在板之間焊接連接的需要。
This product is a collaboration with Brian Kaminski from Advancer Technologies. A portion of each sales goes back to them for product support and continued development.
該產品是與 Advancer Technologies 的 Brian Kaminski 合作推出的。每次銷售的一部分都會返回給他們，以獲得產品支持和持續開發。
- 6x 3.5mm TRS Connectors
- Male Headers Soldered
- Arduino Uno R3 Standard Footprint
- 3.3V/5V Power Jumper
- Board Dimensions
- 53.34mm x 59.69mm (2.10” x 2.35”)
