※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
SparkFun 原廠 u-blox ZED-F9P NEO-D9S Combo Breakout (SPX-20167)－－－停產
更新：
SparkFun GNSS Combo Breakout組合模組 - ZED-F9P, NEO-D9S (Qwiic)（GPS-22560）
SPF原廠 GNSS Combo Breakout組合模組，ZED-F9P、NEO-D9S晶片（GPS-22560）Qwiic
DESCRIPTION
With GNSS, you can know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy, the better! Our versatile global positioning combo breakout pairs the u-blox ZED-F9P multi-band high-precision GNSS module with the NEO-D9S L-band GNSS correction data receiver. With a clear view of the sky, specifically to the South, this combo breakout will deliver centimeter-level accuracy positioning without needing separate RTK or NTRIP corrections!
The ZED-F9P and NEO-D9S combo board raises the bar for high-precision GPS and is one of a line of mighty SparkFun RTK boards. The ZED-F9P is a top-of-the-line module for high-accuracy GNSS and GPS location solutions capable of centimeter-level three-dimensional accuracy. With this board, you will know where your (or any object's) X, Y, and Z location is better than an inch without needing a separate correction source!
We've paired the ZED-F9P with the NEO-D9S-00B satellite data receiver for the L-band correction broadcast. The NEO-D9S can be configured with various L-band correction services, including u-blox's PointPerfect service. It decodes the satellite transmission and outputs a correction stream directly to the ZED-F9P via UART2, enabling the ZED-F9P to reach accuracies down to the centimeter level straight out of the box!
The combo breakout features two USB-C connectors, one for the ZED-F9P and one for the NEO-D9S. With these two connectors, you can hook up the board to your laptop and configure both devices using u-blox u-center if you want to. We've also equipped the board with two Qwiic connectors, so you can connect it quickly and easily to your favorite development board and control it using our sophisticated u-blox GNSS Arduino Library. The ZED-F9P and NEO-D9S share a single SMA antenna connection thanks to a miniature surface-mount power divider (antenna splitter), and 3.3V power is provided for an active antenna. If that wasn't enough, we've provided breakout pads for both devices' I2C, UART1, and UART2 ports on both devices. The UART2 pins are inter-connected (crossed-over) by default so that the NEO-D9S can feed corrections directly to the ZED-F9P, but you can isolate them if you want to by opening the jumper links.／
此組合分線器具有兩個 USB-C 連接器，一個用於 ZED-F9P，一個用於 NEO-D9S。透過這兩個連接器，您可以將開發板連接到筆記型電腦，並根據需要使用 u-blox u-center 配置這兩個裝置。我們還為該板配備了兩個 Qwiic 連接器，因此您可以快速輕鬆地將其連接到您最喜歡的開發板，並使用我們先進的 u-blox GNSS Arduino 庫對其進行控制。
ZED-F9P 和 NEO-D9S 借助微型表面貼裝功率分配器（天線分配器）共享單一 SMA 天線連接，並為主動天線提供 3.3V 電源。如果這還不夠，我們還為這兩個設備上的 I 2 C、UART1 和 UART2 連接埠提供了分線墊。
預設情況下，UART2 引腳是互連（交叉）的，因此 NEO-D9S 可以直接向 ZED-F9P 提供校正，但如果您願意，可以透過開啟跳線連結來隔離它們。
Please note:
PointPerfect L-Band correction service for the SparkFun GNSS Combo Breakout - ZED-F9P, NEO-D9S is currently only available in the USA's 48 contiguous states and the European Union shown in the coverage map below. More information on PointPerfect can be found here.
請注意：SparkFun GNSS Combo Breakout - ZED-F9P、NEO-D9S 的 PointPerfect L 波段校正服務目前僅在美國 48 個鄰近州和歐盟提供，如下面的覆蓋地圖所示。有關 PointPerfect 的更多資訊可在此處找到。
Accessories Required: This product requires a suitable L-Band antenna. Be sure to check out the Hookup Accessories below to pick a suitable antenna for your project.
本產品需要合適的 L 波段天線。請務必查看下面的連接配件，為您的專案選擇合適的天線。
The SparkFun Qwiic Connect System is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can’t hook it up wrong.
FEATURES
［ZED-F9P］ Features 特點 :
- Concurrent reception of GPS, GLONASS, Galileo and BeiDou
- Receives both L1C/A and L2C bands
- ZED-F9P Current Consumption: 68mA - 130mA (varies with constellations and tracking state)
- Time to First Fix 首次修復時間 : 25s (cold), 2s (hot)
- Max Navigation Rate 最大導航速率 :
- PVT (basic location over UBX binary protocol) - 25Hz
- RTK - 20Hz
- Raw - 25Hz
- Horizontal Position Accuracy 水平位置精度 :
- 2.5m without RTK
- 0.010m with RTK
- Operational Limits 操作限制
- Max G: ≤4G
- Max Altitude: 50km (49.7 miles)
- Max Velocity: 500m/s (1118mph)
- 1.5mAh battery backup for RTC
- Default I2C address: 0x42
［NEO-D9S］ Features 特點 :
- Concurrent reception with L-Band Satellite
- Receives L-Band
- Time to First Frame
- User Data Rates
- 600, 1200, 2400, 4800 baud
- Vehicle Dynamics
- Dynamics: +/- 2g acceleration for all data rates (600 bit/s, 1200 bit/s, 2400 bit/s, 4800 bit/s)
- Velocity: Up to and including 300 km/h
- Current Consumption (Acquisition & Tracking):
- Peak: 130mA
- Average: 35mA
- Default I2C address: 0x43
［Breakout Features］ 底板特點（新底板） :
- Input Voltage: 5V or 3.3V but all logic is 3.3V
- 2x USB Type C Connector
- Separate connectors for the ZED-F9P and NEO-D9S
- 2x Qwiic Connectors
- Integrated SMA connector for use with a L1/L2/L-Band antenna of your choice
- On-board power divider (antenna mux)
- 3.3V power for an active antenna
- LEDs
- Power
- RTK (Off: No Carrier Solution; Flashing: Floating Solution; On: Fixed Solution)
- GEO: Geofence
- TP: Timing Pulse (Pulse Per Second)
- Jumpers
- LEDs x 4
- UART2: TX2-RX2 RX2-TX2
- I2C Pull-Up Resistors
- USB Shield
- Board Dimensions 電路板尺寸
- 1.70" x 2.50" (43.2mm x 63.5mm)
Note: The I2C address of the ZED-F9P is 0x42. The I2C address of the NEO-D9S is 0x43. Both are software configurable. A multiplexer/Mux is required to communicate with multiple ZED-F9P modules on a single bus. If you need to use more than one ZED-F9P module, consider using the Qwiic Mux Breakout.
注意：我2ZED-F9P 的 C 位址0x42。我2NEO-D9S的C位址0x43。兩者都是軟體可配置的。需要多路複用器/多路複用器才能與單個總線上的多個ZED-F9P模組進行通信。如果需要使用多個 ZED-F9P 模組，請考慮使用 Qwiic 多路複用器分支。
