產品說明0
※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
Sparkfun原廠 MyoWare 2.0 Power Shield (DEV-18427) 肌肉配件：電池模組
影片：https://youtu.be/d1oUHqPa35I
The MyoWare® 2.0 Power Shield is designed to easily power the MyoWare 2.0 Muscle Sensor for remote applications. The MyoWare Power Shield is equipped with snap connectors on the board so you can easily stack it to the top side of the MyoWare Muscle Sensor. Flip the switch to the ON position to give the sensor all the power it needs to work its myoelectric magic.
MyoWare® 2.0 Power Shield 旨在為遠程應用的 MyoWare 2.0 肌肉傳感器輕鬆供電。 MyoWare Power Shield 在板上配備了卡扣連接器，因此您可以輕鬆地將其堆疊到 MyoWare 肌肉傳感器的頂部。 將開關撥到 ON 位置，為傳感器提供發揮其肌電魔力所需的全部能量。
Each board comes with a 40mAh single cell, lithium polymer (LiPo) soldered to the board. Recharge the battery through the USB Type C connector and its dedicated LiPo charging circuit set to a charge rate of 40mA. This board also includes status LEDs for charging (CHG, FULL, power (VIN), and envelope (ENV). Connecting the MyoWare 2.0 Muscle Sensor to battery power allows for a cleaner signal while also eliminating the possibility of creating a dangerous current path to the power grid. Use it to power your sensor in portable applications.
每塊板都帶有一個 40mAh 的單節電池，鋰聚合物 (LiPo) 焊接到板上。 通過 USB Type C 連接器為電池充電，其專用的 LiPo 充電電路設置為 40mA 的充電速率。 該板還包括用於充電的狀態 LED（CHG、FULL、電源 (VIN) 和包絡線 (ENV)。將 MyoWare 2.0 肌肉傳感器連接到電池電源可以提供更清晰的信號，同時也消除了創建危險電流路徑的可能性 電網。用它為便攜式應用中的傳感器供電。。
Note: This item may take longer to process due to the battery installed in the equipment and therefore does not qualify for same-day shipping policy. Additionally, these batteries can not be shipped via Ground or Economy methods to Alaska or Hawaii. Sorry for any inconvenience this may cause. MyoWare and the Power Shield are not intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation treatment, or prevention of disease, in a man or other animals.
注意： 由於設備中安裝了電池，此項目可能需要更長的時間來處理，因此不符合當日發貨政策的條件。 此外，這些電池不能通過陸運或經濟方式運送到阿拉斯加或夏威夷。 如有不便，敬請原諒。
MyoWare 和 Power Shield 不適用於診斷人類或其他動物的疾病或其他狀況，或用於治愈、緩解治療或預防疾病。
The MyoWare® 2.0 ecosystem consists of shields that easily interface with the MyoWare® 2.0 Muscle Sensor, which is a low-cost, Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies. The innovative connector system allows users to easily snap shields together with a compact low profile and connect to a microcontroller's analog input to measure raw, filtered, and rectified electrical activity of a target muscle. This eliminates the need to solder connections between boards.
MyoWare® 2.0 生態系統由可輕鬆與 MyoWare® 2.0 肌肉傳感器接口的防護板組成，這是一款來自 Advancer Technologies 的低成本、與 Arduino 兼容的一體化肌電圖 (EMG) 傳感器。創新的連接器系統使用戶可以輕鬆地將防護罩與緊湊的薄型連接在一起，並連接到微控制器的模擬輸入，以測量目標肌肉的原始、濾波和整流電活動。這消除了在板之間焊接連接的需要。
This product is a collaboration with Brian Kaminski from Advancer Technologies. A portion of each sales goes back to them for product support and continued development.
該產品是與 Advancer Technologies 的 Brian Kaminski 合作推出的。每次銷售的一部分都會返回給他們，以獲得產品支持和持續開發。
- Input Voltage／輸入電壓
- 5V via USB Type C Connector
- Output Voltage (e.g. "VIN")／輸出電壓
- Nominal Voltage: 3.7V
- Fully Charged: 4.2V
- Power Switch／開關 電源開關
- Built-in LiPo Battery
- Rated Capacity: 40mAh
- Nominal Voltage: 3.7V
- Max Charge Current: 1C (40mA)
- MCP73831 Single Cell LiPo Charge IC
- MyoWare® 2.0 Muscle Sensor Form Factor
- 3x Female Snap Pins (Power and EMG Envelope Output)
- LEDs
- Board Dimensions
- 53.34mm x 59.69mm (2.10” x 2.35”)
