產品說明0
美國原裝 Tag Connector TC2050-IDC (10Pin)
TC2050-IDC 10-Pin “Legged” Plug-of-Nails™ Cable with Ribbon connector
Tag-Connect’s TC2050-IDC “Legged” Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1″ ribbon connector.
- Plugs straight to your PCB – No mating connector or header required!
- Requires only a tiny footprint of pads and locating holes in your PCB.
- Zero Cost Per Board!
- Tiny Footprint!
- High-Reliability Spring-Pins make a Secure Connection and are rated for over 100,000 operations.
- Footprint has no height and can reduce the size and space requirements of your PCB.
- A great way to make test and debug signals available at no cost and with minimal board space.
Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB’s while lowering board costs and facilitating efficient production programming. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB.
The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1″ ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.／此 10 芯電纜一端有 TC2050 標籤連接器，另一端有標準 0.1 英吋帶狀連接器，適用於大多數 MCU/FPGA 以及 JTAG 編程和調試操作。
A growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 (TC2050-IDC-430), etc
See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint.
相關文件
Documents & Media
Datasheet
This product is used in the following debugger/device solutions:
This product is used as part of the following solutions for particular debuggers, protocols and devices. Solutions may involve additional cables, adapters or retaining clips, as well as this product you are viewing now. Click on the solution links to see full solutions and installation instructions where applicable.
- STLINK-V3SET for ST STM32 using JTAG, SWD (via. ARM20)
- PEmicro/P&E Multilink ACP for ARM Cortex using JTAG, SWD
- PEmicro/P&E Cyclone ARM for ARM Cortex using JTAG, SWD
- PEmicro/P&E Multilink Universal/FX for ARM Cortex using JTAG, SWD
- PEmicro/P&E Cyclone LC/FX Universal for ARM Cortex using JTAG, SWD
- ST-LINK/V2 for ST STM32 using JTAG, SWD
- Segger J-LINK for ARM, ARM Cortex using JTAG, SWD
- Intel/Altera Byte Blaster for Intel (Altera) using Altera JTAG (10 pin target connector)
- Xilinx Platform Cable for Xilinx using JTAG
- TI XDS100v2 for TI DSPs using JTAG
- XJTAG for Intel (Altera), Xilinx, Lattice, MicroSemi (Microchip) using JTAG
- Digilent JTAG-HS2/HS3 for Xilinx using JTAG
- Lattice HW-USBN-2B for Lattice using JTAG, SPI/PDI/μPDI/aWire/debugWIRE
- Intel/Altera USB Blaster for Intel (Altera) using Altera JTAG (10 pin target connector)
- Renesas E1/E2/E8a/E20 for Renesas Various using JTAG/FINE
- Silicon Labs USB Debug Adapter for Silicon Labs 8-bit MCUs using JTAG/C2
- PEmicro/P&E Multilink Universal/FX for NXP Various using Various
- PEmicro/P&E Cyclone LC/FX Universal for NXP Various using Various
