產品說明0
※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
Sparkfun原廠 MyoWare 2.0 LED Shield (DEV-18387) 肌肉配件：LED 模組
影片：https://youtu.be/d1oUHqPa35I
The MyoWare® 2.0 LED Shield is designed to display the magnitude of a target muscle's signal and power the MyoWare 2.0 Muscle Sensor with its built-in battery. The blue 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board LEDs will go! With this shield, you will be provided with a visual representation of the signals provided by the MyoWare 2.0 Muscle Sensor. The LED shield is equipped with snap connectors on the board so you can easily stack it on the top side of the MyoWare 2.0 Muscle Sensor and flip the switch to the ON position to give the sensor all the power it needs to work its myoelectric magic.
MyoWare® 2.0 LED 護罩旨在顯示目標肌肉信號的大小，並通過內置電池為 MyoWare 2.0 肌肉傳感器供電。 藍色的 10 段條形圖顯示了測量信號的幅度。 測量的肌肉激活越多，電路板 LED 就越高！ 使用此防護罩，您將獲得由 MyoWare 2.0 肌肉傳感器提供的信號的可視化表示。 LED 護罩在板上配備了卡扣連接器，因此您可以輕鬆地將其堆疊在 MyoWare 2.0 肌肉傳感器的頂部，並將開關撥至 ON 位置，為傳感器提供發揮其肌電魔力所需的全部功率。
Each board comes with a 40mAh single cell, lithium polymer (LiPo) battery soldered to the board. Recharge the battery through the USB Type C connector and its dedicated LiPo charging circuit set to a charge rate of 40mA. This board also includes status LEDs for charging (CHG, FULL, and power (VIN)). Connecting the MyoWare 2.0 Muscle Sensor to battery power allows for a cleaner signal while also eliminating the possibility of creating a dangerous current path to the power grid. Use it to gauge how hard you’re working a muscle during a workout, as a teaching tool, or add some myoelectric flair to your Halloween costume!
每塊板都帶有一個焊接到板上的 40mAh 單節鋰聚合物 (LiPo) 電池。 通過 USB Type C 連接器為電池充電，其專用的 LiPo 充電電路設置為 40mA 的充電速率。 該板還包括充電狀態 LED（CHG、FULL 和電源 (VIN)）。 將 MyoWare 2.0 肌肉傳感器連接到電池電源可以提供更清晰的信號，同時還消除了在電網中創建危險電流路徑的可能性。 用它來衡量你在鍛煉期間鍛煉肌肉的強度，作為教學工具，或者為你的萬聖節服裝增添一些肌電天賦！
Note: This item may take longer to process due to the battery installed in the equipment and therefore does not qualify for same-day shipping policy. Additionally, these batteries can not be shipped via Ground or Economy methods to Alaska or Hawaii. Sorry for any inconvenience this may cause. MyoWare and the LED Shield are not intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation treatment, or prevention of disease, in a man or other animals.
注意： 由於設備中安裝了電池，此項目可能需要更長的時間來處理，因此不符合當日發貨政策的條件。 此外，這些電池不能通過陸運或經濟方式運送到阿拉斯加或夏威夷。 如有不便，敬請原諒。
MyoWare 和 LED Shield 不適用於診斷人類或其他動物的疾病或其他狀況，或用於治愈、緩解治療或預防疾病。
The MyoWare® 2.0 ecosystem consists of shields that easily interface with the MyoWare® 2.0 Muscle Sensor, which is a low-cost, Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies. The innovative connector system allows users to easily snap shields together with a compact low profile and connect to a microcontroller's analog input to measure raw, filtered, and rectified electrical activity of a target muscle. This eliminates the need to solder connections between boards.
MyoWare® 2.0 生態系統由可輕鬆與 MyoWare® 2.0 肌肉傳感器接口的防護板組成，這是一款來自 Advancer Technologies 的低成本、與 Arduino 兼容的一體化肌電圖 (EMG) 傳感器。創新的連接器系統使用戶可以輕鬆地將防護罩與緊湊的薄型連接在一起，並連接到微控制器的模擬輸入，以測量目標肌肉的原始、濾波和整流電活動。這消除了在板之間焊接連接的需要。
This product is a collaboration with Brian Kaminski from Advancer Technologies. A portion of each sales goes back to them for product support and continued development.
該產品是與 Advancer Technologies 的 Brian Kaminski 合作推出的。每次銷售的一部分都會返回給他們，以獲得產品支持和持續開發。
- Input Voltage
- 5V via USB Type C Connector
- Output Voltage (e.g. "VIN")
- Nominal Voltage: 3.7V
- Fully Charged: 4.2V
- Power Switch
- Built-in LiPo Battery
- Rated Capacity: 40mAh
- Nominal Voltage: 3.7V
- Max Charge Current: 1C (40mA)
- MCP73831 Single Cell LiPo Charge IC
- MyoWare® 2.0 Muscle Sensor Form Factor
- 3x Female Snap Pins (Power and EMG Envelope Output)
- LEDs
- VIN
- FULL
- CHG
- 2x 5-Segment Bars
- Board Dimensions
- 46.15mm x 38.00mm (1.82” x 1.50”)
