※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
The ShiftBar is a medium-power RGB LED controller featuring 10-bit digital brightness control on each color channel (over one billion colors). Multiple ShiftBar modules can be chained together and controlled from a single microcontroller to create large LED displays.
你還在傷腦筋該如何控制你手邊的彩色LED模組的顏色與光感度。
ShiftBar 是一個內建10-bit亮度控制的LED 驅動模組，它可以超過一百萬個顏色。這個LED模組可以彼此串連起來形成一個LED屏幕，並透過一個微處理便其中的3個pin角便可以控制這個大型的LED屏幕。
它與ShiftBrite V2.0控制功能相同，只是ShiftBar 本身沒有LED，它是專門給RGB LED燈或燈條使用的。
Overview
The ShiftBar is a 3-channel constant current LED driver module by macetech based on the Allegro A6281. This is a carrier board that is similar to the ShiftBrite, but designed for controlling external RGB LED modules, such as the ultra-bright Satellite Module 001. Using just three digital output pins and a simple protocol, your microcontroller can control a long chain of ShiftBars. Each ShiftBar in the chain can be independently changed to any of the 1,073,741,824 possible colors to create dynamic displays and decorations.
- Supplies 10 mA to 150 mA per LED channel.
- On-board potentiometer for current control.
- Input voltage range from 5 V to 17 V, with no separate logic supply required.
- Overtemperature shutdown protects the LED driver from overheating.
- Adjustable current for each color channel lets you correct for slight differences in brightness.
The ShiftBar can also be used with the lower-power 003 and 004 satellite modules, though if you want to control more than one, we recommend you use the OctoBrite, which can control up to eight of these satellite modules.
Example ShiftBar applications
An example setup using a Micro Maestro to control a ShiftBar (or chain of ShiftBars) is shown below. Digital outputs 0, 1 and 2 are used to send the control signals to the clock, latch, and data lines, the enable line is connected directly to GND, and 12V power to the Maestro is delivered from the ShiftBar chain. Maestro source code to control a ShiftBar is available in the Example scripts section of the Maestro User’s guide.
 |
| Connecting the Micro Maestro to a chain of ShiftBars. A single 12V supply powers all of the devices. |
視頻：
http://www.youtube.com/watch?feature=player_embedded&v=-27CQ_d7YSg
A similar setup can be used to connect the ShiftBar to other controllers, such as the Baby Orangutan, Arduino, or BASIC Stamp.
In the Halloween display below, each pumpkin contains a Satellite Module, and the entire display is driven by a single ShiftBar chain, controlled by a microcontroller. Details of the project are available here.
視頻：
http://www.youtube.com/watch?v=qJIjwZnU-dw&feature=player_embedded
Using the ShiftBar
The pinout of the ShiftBar module is shown below. As with the ShiftBrite, signals are sent in to the CI, EI, LI, and DI pins, and these signals are sent out to the CO, EO, LO, and DO pins. Terminal blocks are provided for the power connections and the connections to the external LEDs, which should be configured in a common anode (low-side switch) arrangement. Our custom six-conductor cables, available in lengths of 6" and 12" and 24", can be used to easily chain together multiple modules. You can make your own shorter cables with our 3" wires with pre-crimped terminals and our 0.1" 6×1 crimp connector housings.
如下的接線，CI, DI, LI和EI 與( CO, EO, LO, and DO)是板子與板子互相接的pin角，下方的端子台則是給LED電流與連接外部LED燈的端子。
上方的旋鈕端子，則是可以設定輸出給LED電流大小的旋鈕。
The ShiftBar is pin-compatible with the ShiftBrite, so for further details and example code, please see the instructions on the ShiftBrite page. We also recommend careful reading of the Allegro A6281 datasheet (315k pdf) as well as the macetech documentation page.
