洋天科技洋天科技
公司簡介訂購方式匯款確認檔案下載 聯絡我們保固說明訂單查詢討論區
電子郵件:

密碼:

忘記密碼
加入會員
  首頁 | 原廠 Arduino® | 特殊服務設計 | 轉接座及轉接板/麵包板 | 開發板/燒錄器/模擬器 | 相容 For Arudino® 週邊及配件 | OKdo系列 | Saleae 系列 | Adafruit 系列 | ArduCam 系列 | Camera 攝像頭 | ROCK 系列 | Debix系列開發板 | Raspberry Pi 樹莓派 | Banana Pi 香蕉派 | BeagleBone 狗骨頭 | M5Stack系列 | Micro:bit (BBC)系列 | NVIDIA Jetson Nano系列 | Pololu 系列 | Pycom 系列 | Seeed 系列 | Sparkfun 系列 | WeMos 系列 | 傳感器 | Cubieboard/CubieTruck系列 | Firefly 系列 | Microduino系列 | Orange Pi 香橙派 | PCB板 | PLC 系列 | Robot 機器人 | UDOO 系列 | RedBearLab 系列 | LattePanda系列 | LittleBits 系列 | Libelium 系列 | Luxonis 相機系列 | PCduino | RobotElectronics 系列 | MageDok 顯示屏 | LCD/LCM/TFT/LVDC | Dimension Engineer 系列 | 通訊模組 | 影音器材(含轉換器) | 線材/連結器/轉換器 | 測量儀器 | 馬達/馬逹控制器/電源模組 | 其他 | 焊接/維修工具 | IC零件 | LED燈-裝飾燈 | 工作站迷你電腦 mini PC | 擴大器 | 雕刻機 | 電池 | 電腦周邊 | 檢定考套件 | 停售商品
  首頁 » 商品目錄 » Pololu 系列 » Motion Control Modules » 43326217
商品搜尋 進階
 |  購物車內容  |  結帳   
商品分類
  DRVXXXX系列
  Electronics
  G2 High-Power Motor Drivers
  Mechanical Components
  Motion Control Modules
    RC Servo Controllers
  Robot Kits
  Sensors
Arduino
Pololu
Seeed
Sparkfun
robot-electronics
dimensionengineering
libelium
adafruit
udoo
redbearlab
Arducam
goembed
Saleae
okdo
服務台
公司簡介
退換貨服務
訂購方式
聯絡我們
匯款確認
[<< 前一頁]  瀏覽相同分類產品 7 / 27  [下一頁 >>]
●現貨 Pololu原廠 VNH5019 Motor Driver Carrier 電機驅動(PI1451)
NT$2,000
運費NT$50
條碼43326217
產品說明

※本產品原廠代理從國外進口,有些交期較長,下訂前請詢問!

  This carrier board for ST’s VNH5019 motor driver IC operates from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak). It works with 2.5 to 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current sense feedback (an analog voltage proportional to the motor current). Along with built-in protection against reverse-voltage, over-voltage, under-voltage, over-temperature, and over-current, these features make this product a great general-purpose motor driver.

Overview

  

VNH5019 motor driver carrier, bottom view with dimensions.

 

   This module is a compact breakout board for ST’s high-power VNH5019 motor driver IC, a fully integrated H-bridge that can be used for bidirectional speed control of a single brushed DC motor. The basic operation of the driver is summarized below, but we also recommend careful reading of the VNH5019 datasheet (629k pdf) before using this product. The board incorporates most of the components of the typical application diagram on page 14 of the VNH5019 datasheet, including pull-up and current-limiting resistors and a FET for reverse battery protection. It ships fully populated with its SMD components, including the VNH5019, as shown in the product picture.

 

【Features】

 

  • Operating voltage: 5.5 – 24 V1
  • Output current: 12 A continuous (30 maximum)
  • 3V-compatible inputs
  • PWM operation up to 20 kHz, which is ultrasonic and allows for quieter motor operation
  • Current sense output proportional to motor current (approx. 140 mV/A)
  • Motor indicator LEDs (indicates what the outputs are doing even when no motor is connected)
  • Robust:
    • Reverse-voltage protection
    • Can survive input voltages up to 41 V
    • Undervoltage and overvoltage shutdown
    • High-side and low-side thermal shutdown
    • Short-to-ground and short-to-Vcc protection

1 While the overvoltage protection typically kicks in at 27 V, it can trigger at voltages as low as 24 V, so we do not recommend using this motor driver with 24 V batteries, which significantly exceed 24 V when fully charged.

【Using the Motor Driver】

 The motor and motor power connections are on one side of the board and the control connections are on the other side. The motor power supply connects to the large VIN and GND pins; it should be between 5.5 and 24 V and have the ability to deliver the potentially high currents the motor will require. The logic power supply (typically 2.5 – 5 V) connects to the small VDD and GND pads on the control side of the board and is used to power the internal pull-ups on the ENA and ENB enable lines. Any control input voltage above 2.1 V is guaranteed to be high, so this driver can be directly interfaced into both 3.3 and 5 V systems.

 The following diagram shows the minimum connections required for interfacing this motor driver with a microcontroller:

 

Minimal wiring diagram for connecting a microcontroller to a VNH5019 motor driver carrier.

  

  In this configuration, motor direction is determined by the states of the INA and INB pins and motor speed is controlled by the duty cycle of a PWM signal supplied to the driver’s PWM pin. The PWM pin is pulled low on the board, so the motor driver outputs are effectively disabled by default; the INA and INB pins are floating (they are not pulled to any particular default voltage). See the truth tables in the VNH5019A-E datasheet for more information on how the INA, INB, and PWM pins affect the driver outputs, OUTA and OUTB. Note that it is also possible to save a microcontroller I/O line by directly PWMing the INA and INB pins while holding the PWM pin high (e.g. by connecting it directly to VDD).

  This board features motor indicator LEDs that can be used to test that motor driver outputs are working as expected before actually connecting a motor (this can be especially helpful in detecting problems due to insufficient power supplies). The LED brightness with increase with motor speed, and the LED color changes with direction.

【Pinout】

 

 

 

PIN Default State Description
VIN   The connection point for the positive side of the 5.5 – 24 V motor power supply. Since the overvoltage protection can be as low as 24 V, we do not recommend using 24V batteries for VIN.
VDD   The connection point for the positive side of the logic power supply (typically 2.5 – 5 V). The only function of this pin is to power the internal pull-ups on the two enable lines, ENA and ENB.
VOUT   This pin gives you access to the motor power supply after the reverse-voltage protection MOSFET (see the board schematic below). It can be used to supply reverse-protected power to other components in the system, but it should not be used for high currents. This pin should only be used as an output.
GND   Ground connection points for logic and motor power supplies. The control source and the motor driver must share a common ground.
OUTA   Output of half-bridge A (connects to one terminal of a DC motor).
OUTB   Output of half-bridge B (connects to the other terminal of a DC motor).
PWM LOW Pulse width modulation input: a PWM signal on this pin corresponds to a PWM output on the motor outputs.
INA FLOAT Motor direction input A (“clockwise” input).
INB FLOAT Motor direction input B (“counterclockwise” input).
CS   Current sense output. The pin voltage is roughly 140 mV per amp of output current when the CS_DIS pin is low or disconnected. The current sense reading is more accurate at higher currents. (Note that while the CS voltage can potentially exceed 3.3 V at high currents, the current sense circuit should be safe for use with many 3.3V analog inputs. Most MCUs have integrated protection diodes that will clamp the input voltage to a safe value, and since the CS circuit has a 10 kΩ resistor in series with the output, only a few hundred microamps at most will flow through that diode.)
ENA/DIAGA HIGH Combination enable input/diagnostic output for half-bridge A. When the driver is functioning normally, this pin acts as an enable input, with a logical high enabling half-bridge A and a logical low disabling half-bridge A. When a driver fault occurs, the IC drives this pin low and half-bridge A is disabled. This pin is connected to VDD through a pull-up resistor on the board.
ENB/DIAGB HIGH Combination enable input/diagnostic output for half-bridge B. See the description of ENA/DIAGA.
CS_DIS LOW Disables the current sense output, CS, when high. Can be left disconnected in most applications.

【Included Hardware】

  A 20-pin 0.1″ straight breakaway male header and two 2-pin 5mm terminal blocks are included with the motor driver as shown in the picture below. You can use the terminal blocks to make your motor and motor power connections, or you can break off an 8×1 section of the 0.1″ header strip and solder it into the smaller through-holes that border the four large motor and motor power pads. Note, however, that the terminal blocks are only rated for 16 A, and each header pin pair is only rated for a combined 6 A, so for higher-power applications, thick wires should be soldered directly to the board. 

VNH5019 motor driver carrier with included hardware.

 

 Soldering the 0.1″ headers to the logic connections enables use with custom cables or solderless breadboards, or wires can be soldered directly to the board for more compact installations. Motor and motor power connections should not be made through a breadboard.

 The motor driver includes a 47 uF electrolytic power capacitor, and there is room to add additional capacitors (e.g. to compensate for long power wires or increase stability of the power supply). Additional power capacitors are usually not necessary, and no additional capacitors are included with this motor driver.

 The two mounting holes are intended for use with #2 screws (not included).

【Schematic Diagram】

Schematic diagram for the Pololu VNH5019 motor driver carrier.

 

   This schematic is also available as a downloadable pdf: VNH5019 carrier schematic (34k pdf)

Note: All boards shipped from Pololu prior to October 28, 2011 have 1.5k current sense resistors (R10 in the schematic above), which results in a current sense (CS) output of approximately 210 mV/A. That resistor has now been changed to 1k for better compatibility with 3V systems, producing a CS output of approximately 140 mV/A.

【VNH3SP30, VNH2SP30, and VNH5019 Comparison 】

Thermal image of the underside of the VNH5019 motor driver carrier during one of our current tests.

 

   In addition to this VNH5019 carrier, we offer carrier boards for two similar, older motor drivers from ST: the VNH3SP30 and the VNH2SP30. The VNH5019 is the only one of the three with a practical operating voltage above 16 V, and it is the only one that works with 3 V logic.

  The current-related values in the table below (i.e. the entries to which footnote 3 applies) are the results of tests on only one or two of each driver version, so they do not capture potential unit-to-unit variation. As such, the values should be treated as rough estimates of performance, not as performance guarantees. While these tests seem to indicate that the VNH2SP30 runs a bit cooler—and hence can deliver more continuous current—than the VNH5019, it is important to note that the three driver versions were tested at different times under potentially different conditions, so the results are not necessarily accurate indications of relative performance.

  In our tests, we noticed that the thermal protection on the VNH5019 was activating at a lower temperature (153°C) than on the VNH2SP30 (170°C), which could partially account for the shorter VNH5019 overheating times. However, we also observed that the VNH5019 was reaching slightly higher temperatures than the VNH2SP30 when used under the same conditions: the VNH5019 reached a temperature of 85°C after 3 minutes at 10 A while the VNH2SP30 reached a temperature of 80°C.

 

The following table offers a comparison of the three drivers:

1 The VNH3SP30 can survive input voltages up to 40 V, and the VNH2SP30 and VNH5019 can survive input voltages up to 41 V, but the over-voltage shutoff will kick in at lower voltages.

2 While VNH3SP30’s over-voltage shutoff doesn’t activate until 36 V, in our experience, shoot-through currents make PWM operation impractical above 16 V.

3 Typical results using the Pololu motor driver carrier boards with 100% duty cycle at room temperature (with no forced airflow or heat sinking beyond the carrier PCB).

【Real-world power dissipation consideration】

 The motor driver IC has a maximum continuous current rating of 30 A. However, the chips by themselves will overheat at lower currents (see the table above for typical values). The actual current you can deliver will depend on how well you can keep the motor driver cool. The carrier’s printed circuit board is designed to draw heat out of the motor driver chips, but performance can be improved by adding a heat sink. In our tests, we were able to deliver short durations (on the order of milliseconds) of 30 A and several seconds of 20 A without overheating. At 6 A, the chip gets just barely noticeably warm to the touch. For high-current installations, the motor and power supply wires should also be soldered directly instead of going through the supplied terminal blocks, which are rated for up to 16 A.

 This product can get hot enough to burn you long before the chip overheats. Take care when handling this product and other components connected to it.

 Many motor controllers or speed controllers can have peak current ratings that are substantially higher than the continuous current rating; this is not the case with these motor drivers, which have a 30 A continuous rating and over-current protection that can kick in as low as 30 A (50 A typical). Therefore, the stall current of your motor should not be more than 30 A. (Even if you expect to run at a much lower average current, the motor can still draw short bursts of high currents, such as when it is starting, if special steps are not taken.)

Note: The datasheet refers to the motor driver IC by the full part number VNH5019A-E, but the “A” seems to simply indicate that it was packaged in tubes. It mentions VNH5019TR-E as another valid part number for this IC (indicating tape-and-reel packaging).

問與答

顯示 1 到 第4 (共 4 則 問與答) 總頁數:  1 
會員 BruceLai先生/小姐 詢問: 2018-08-30  14:57:01
問題: 你好
請問目前這款驅動電路是否有現貨呢?
回覆: 訂貨二,三週
下面這款有現貨
http://twarm.com/commerce/product_info.php?products_id=6214
會員 BruceLai先生/小姐 詢問: 2018-08-30  14:56:18
問題: 你好
請問這款目前是否有現貨呢?
回覆: 大約二,三週才會有

下面這款有
http://twarm.com/commerce/product_info.php?products_id=6214
訪客 詢問: 2018-05-24  12:19:49
問題: 您好想請問您有關VNH5019的相關問題
VNH5019Motor Driver Carrier這款產品要接馬達的正反轉是要接到哪裡呢
回覆: 您好,你可以寫信到i0104@ms13.hinet.net詢問
訪客 詢問: 2016-08-08  15:28:22
問題: 你好
我想請問一下你們那邊現在有六個VNH5019 motor driver嗎?
http://twarm.com/commerce/product_info.php?products_id=6217
謝謝
回覆: 您好,剩一個
訂要大約一,二週時間
顯示 1 到 第4 (共 4 則 問與答) 總頁數:  1 
本商品上架日期:2013-05-23.
評價
購物車 更多
1 x ●(特價*/現貨) Nano Proto Board 開發板/洞洞板+時鐘模塊,RedBearLab 原廠(台灣獨家代理)
1 x 51 AVR usbasp usbisp脫機編程器 離線全流程可配置 支持序列號
1 x 2inch LCD Module / 2寸 IPS顯示屏 240×320
1 x 香橙派 Orange Pi ONE 開發板(全志 H3芯片),升級1G內存、開源編程單片機
1 x 3DB30+ (光電隔離+鍍金接口) / 6ES7901-3DB30-0XA0 PLC編程電纜 下載線 西門子S7-200
1 x Addressable RGB 30-LED Strip, 5V, 1m (WS2812B)
1 x 0.95inch RGB OLED (A),樹莓派Raspberry Pi 0.95寸 SSD1331顯示屏 彎排針
1 x 20路PLC放大板 板保護板 晶體管 輸出板 SL-20MT 功率板
1 x #&●(現貨,當日寄出)2021新品 Raspberry Pi Pico 高性能微控制器板 RP2040 開發板
1 x &NVIDIA JETSON XAVIER NX (8GB)SUB版本,英偉達 開發板 (單主板)
1 x ●香蕉派 Banana Pi M2+(H2+) (BPI-M2+) 四核開發板 全志H2+ 1GB DDR3 RAM
1 x WeMos D1 mini 配件 / WS2812B RGB 擴展板
1 x $樹莓派 Raspberry Pi Compute module 4 (標準2GB RAM+ 8G eMMC) CM4
1 x 電壓隔離採樣,數字電流表,瓦時計,電池監控儀表
1 x 10路PLC放大板 輸出板 輸入NPN 輸出PNP 光電隔離
1 x ●K0系列TJC3224K024_011RN,2.4寸 增強型 USART HMI 串口屏組態屏擴展IO EEPROM TFT
1 x LattePanda V1拿鐵熊貓專用:Gravity I/O擴展板 兼容Arduino傳感器 (DFR491)
1 x >香蕉派 Banana Pi M3 外殼 BPI-M3 BPI-M2U 鋁合金外殼
1 x ●WeMos D1 Pro mini - 16 m 外部天線連接器ESP8266無線物聯網
1 x (AD827接線座接口)音樂傳真A1前級板功放板前級317 337高精度穩壓AD827運放成品板
1 x *NVIDIA Jetson Nano Developer Kit 桌上型(全配1,不含主板)
1 x #【原廠7吋螢幕,加價升級】SmartiPi Touch Pro 標配:黑色S款→ 白色S款
1 x >(B0055停產,新款請看B0428)原廠M12*高0.5 OV5647攝像頭 1080P魚眼鏡頭-LS-40180 樹莓
1 x NTS300 第4代(單鏡頭直徑7.6MM+1M長硬線)6LED 升級5寸屏 4倍放大 工業內窺鏡 防水夜視檢測 攝像機汽車/空
1 x (DC6-30V)USB-TTL聲光報警器蜂鳴器24V防水警報器報警燈定制語音YX75R
1 x >(停產,參考新版LTS版本) 香橙派 OrangePi R1 Plus 開發板
1 x 香蕉派 Banana Pi BPI-Bit 雲端物聯網開發板
1 x 香蕉派 banana pi (BPI-M64/M2U/M2+) 專用 攝像頭 OV5640 camera
1 x &●樹莓派 Raspberry Pi HQ Camera / 高質量攝像頭模塊 IMX477 可支持1230萬像素 (不含鏡頭)
1 x (YYAC-2)可控矽模塊 晶閘管控制板 觸發開關 直流控制交流220V 光耦隔離
1 x A4988 A4983 3D打印機機驅動模塊 步進電機驅動器
1 x #&●2017年 樹莓派Pi3B 英國版UK Raspberry Pi 3B Model B (pi2B 升級版)(4代)
1 x 乙級硬體裝修 (10包)
1 x LattePanda、樹莓派Raspberry Pi 專用 帶觸摸板的無線鍵盤 2.4G無線鍵盤鼠標 (DFR330)
1 x ●PiCAN2 Duo CAN-Bus 模組,Pi 4 專用 with 3A SMPS(RSP-PICANDUOSMPS3A)
1 x ★Magedok 原廠 15.6 吋 顯示屏 顯示器 3840x2160 4K HD IPS Dispaly(156A)
1 x ●LattePanda V1 專用外殼 透明外殼 Acrylic Case(FIT474)
1 x BOOSTXL-BASSENSORS
1 x ROS2機器人SLAM麥克納姆輪無人小車(ROSMASTER X3系列)-配套【旗艦版,配雷達S2L】不含JETSON NANO
1 x W78E052B
1 x ODROID-XU4開發板 含風扇 送專用電源 Samsung Exynos5422處理器
1 x 2.7inch NFC-Powered e-Paper Module(模組)2.7寸 無源NFC電子墨水屏模塊
1 x RP2040-Matrix 迷你開發板 板載5×5 RGB LED矩陣 樹莓派微控制器開發板
1 x ●AD7705 雙路16位ADC數據採集模塊(不焊4pin),輸入增益可編程SPI接口
1 x 專案規劃(電子商品開發與設計)
1 x ▼●(現貨*)IMX219-160 IR-CUT 800萬像素 夜視攝像頭Camera 視角160度,NVIDIA Jetson
1 x (現貨) FLIR Lepton 開發套件V1.4 底板 (不含鏡頭) (250-0587-00)
1 x 焊接助手裝機台 FPV 穿越機固定八爪工作台 適用分電板 電路板的焊接 (6爪工作平台)
1 x $請先詢價(預購)UDOO BOLT V3 開發板, 嵌入式 V1202B 雙核 4線程@ 2.3ghz
1 x 10.1inch HDMI LCD (E) / 樹莓派Raspberry Pi 10.1寸 電容屏 IPS 1024×600
1 x GAL22V10
1 x 海備思 HAGiBiS Type-C擴充器 USB3.0 X4 PD供電口((五合一)USB+供電款)0.12M
1 x ●香蕉派 banana pi 專用 充電器 電源 適配器
1 x &$●US美規 樹莓派 Raspberry Pi 400 Personal Computer Kit 套件(含書)pi400
1 x (書BOOK)樹莓派 Python編程指南 / 開發教程書籍 入門到精通 9787111489863
1 x 4.2inch e-Paper Cloud Module模組,4.2寸 電子墨水屏模塊 400×300
1 x ●香橙派 Orange Pi5/Pi5B 開發板專用:壓克力保護殼+風扇
1 x $(預購)樹莓派 Pi Compute module 4 (標準2GB RAM+無eMMC) CM4 Lite 簡易版
1 x JETSON-IO-BASE-A,Jetson Nano 擴展板 底板(核心板、散熱風扇另購)
1 x 電動車摩托車/汽車 蓄電池測試儀 檢測表電瓶/容量電壓表
1 x ●10pcs一標 AD620AN AD620 PDIP8
1 x &NVIDIA JETSON TX2-NX(4GB)英偉達 開發板 (單主板)
1 x (0.3間距41P同向160MM)FPC鍍金雙排 軟排線 測試線
1 x NVIDIA® Jetson AGX Orin™ Developer Kit 開發者套件 32GB,最強大的 AI 邊緣計算機
1 x (特價*)D1 MINI V2 開發板 (ESP-12F) / NodeMcu Lua WIFI 基于ESP8266迷你
1 x >(停產,替代款B0381)型號:B0110,Arducam AR0134 1.2MP 全局快門 黑白攝像機模塊
1 x 萊曼(lehmann)耳機放大器DIY 耳放前級帶保護(成品機)
1 x &最新 Raspberry Pi 4 B (是新版Pi4B) 8GB RAM內存 type-C (送贈品)
1 x ▼ARPI600 擴展板 + 13塊 傳感器模塊(樹莓派 配件包 PI4B Sensor Acce)
1 x DFROBOT原廠 基礎焊接套裝 帶收藏包 KIT077
1 x XW16Pro脫機燒錄器(C.僅支援GD32)支持掃碼燒錄控制 1拖2燒錄 編程器STM32
1 x GamePi43 套餐(含Pi3B+、32G卡),樹莓派 Raspberry Pi3B 掌上遊戲機擴展板 (含4.3寸顯示屏)
1 x 型號:B0216,Arducam 18MP AR1820HS Color 彩色相機模塊,適用於 Jetson Nano
1 x RP2040-One 開發板Type-A版
1 x &*(現貨)NVIDIA Jetson Nano Developer Kit 桌上型(全配1,含主板B01)
NT$10,679,867
查詢訂單狀態
 
請輸入您的訂單編號
商品通知狀態 更多
通知●現貨 Pololu原廠 VNH5019 Motor Driver Carrier 電機驅動(PI1451)
更新時通知我
推薦給朋友
 
推薦這個商品給朋友

聯絡方式:手機:0933807110 或 0968222607
E-mail:i0104@ms13.hinet.net(主要信箱) & i03070309@yahoo.com.tw(次要) & a_te0307@hotmail.com & A9215017@mail.ntust.edu.tw & r94922042@ntu.edu.tw