洋天科技洋天科技
公司簡介訂購方式匯款確認檔案下載 聯絡我們保固說明訂單查詢討論區
電子郵件:

密碼:

忘記密碼
加入會員
  首頁 | 原廠 Arduino® | 特殊服務設計 | 轉接座及轉接板/麵包板 | 開發板/燒錄器/模擬器 | 相容 For Arudino® 週邊及配件 | OKdo系列 | Saleae 系列 | Adafruit 系列 | ArduCam 系列 | Camera 攝像頭 | ROCK 系列 | Debix系列開發板 | Raspberry Pi 樹莓派 | Banana Pi 香蕉派 | BeagleBone 狗骨頭 | M5Stack系列 | Micro:bit (BBC)系列 | NVIDIA Jetson Nano系列 | Pololu 系列 | Pycom 系列 | Seeed 系列 | Sparkfun 系列 | WeMos 系列 | 傳感器 | Cubieboard/CubieTruck系列 | Firefly 系列 | Microduino系列 | Orange Pi 香橙派 | PCB板 | PLC 系列 | Robot 機器人 | UDOO 系列 | RedBearLab 系列 | LattePanda系列 | LittleBits 系列 | Libelium 系列 | Luxonis 相機系列 | PCduino | RobotElectronics 系列 | MageDok 顯示屏 | LCD/LCM/TFT/LVDC | Dimension Engineer 系列 | 通訊模組 | 影音器材(含轉換器) | 線材/連結器/轉換器 | 測量儀器 | 馬達/馬逹控制器/電源模組 | 其他 | 焊接/維修工具 | IC零件 | LED燈-裝飾燈 | 工作站迷你電腦 mini PC | 擴大器 | 雕刻機 | 電池 | 電腦周邊 | 檢定考套件 | 停售商品
  首頁 » 商品目錄 » Raspberry Pi 樹莓派 » Pi Camera攝像頭、外殼、支架 » 208417712
商品搜尋 進階
 |  購物車內容  |  結帳   
商品分類
  *Pi 主板*
  *SD卡
  ✨Pi5 B系列 (配件不共用) Type-C 供電
  *供電擴展板UPS(含電池、不含電池)
  ✨Pi 4 B系列 (配件不共用) Type-C 供電
  *Arducam原廠(攝像頭、擴展板)
  *風扇、散熱
  ✨Pi CM 系列 Raspberry Pi Compute
  ✨Pi Pico 系列(micro USB供電)
  ✨Pi Zero、Zero W 系列(micro USB供電)
  *PICAN 擴展板
  Pi Camera攝像頭、外殼、支架
    單顆:鏡頭Lens
    外殼 / 支架
    連接線 FFC/FPC
    100萬 1MP
    200萬 2MP
    500萬 5MP
    800萬 8MP
    1200萬.. 12MP
    1300萬以上...13MP
  Pi LCD LED 屏
  ✨Pi 1、2B、3B+(共用電源)micro USB供電
  ✨Pi 400 系列(Type-C USB供電)
  傳感器模組
  小車 智能車 Car
  擴展板
  網卡(USB、WiFi ....)
  鍵盤/遙控器/手把 手柄
  音頻/功放/喇叭
  Pi 3A+ Case 外殼
  DEXTER原廠
  乙太網
  Allo系列
  Pimoroni系列
  ◎總覽
  其它
  Pi 1B板專用:擴展板/模組/外殼 26PIN
  Book書
Arduino
Pololu
Seeed
Sparkfun
robot-electronics
dimensionengineering
libelium
adafruit
udoo
redbearlab
Arducam
goembed
Saleae
okdo
服務台
公司簡介
退換貨服務
訂購方式
聯絡我們
匯款確認
[<< 前一頁]  瀏覽相同分類產品 35 / 47  [下一頁 >>]
Raspberry Pi Camera HDMI Cable Extension樹莓派 攝像頭轉板 擴充HDMI線(1對2組)
NT$1,500
運費NT$50
條碼208417712
產品說明

 

※本產品原廠代理從國外進口,有些交期較長,下訂前請詢問!

以 下 為 示 範 圖↓↓↓↓↓↓↓↓

以 下 為 出 貨 清 單↓↓↓↓↓↓↓↓

A set of connectors to extend the Raspberry Pi camera cable with a standard HDMI cable. Important news: it works with the V1 & V2 cameras.

This is a kit to use a standard HDMI cable between the Raspberry Pi and its camera. The biggest advantages are obviously the range increase, the possibility to use widely available cables, and to use a round and sturdy HDMI cable instead of a flat ribbon. Note that this is just an extension between the camera and the Raspberry Pi. Four additional pins are available, this may become handy to use a few sensors with low current requirement along with your camera. The parts in the kit are shown in the third picture, every board is tested before shipping. This system works with all Raspberry Pi models.

I am using the Pi camera outside the house and close to machinery so I needed a longer and stronger cable with solid connections. Searching the web I did not find anything usable for my application. However a thread on the Raspberry Pi forum gave me the idea to try using an HDMI cable for extension. By comparing the diagram of the Pi Camera connector and HDMI connector one can see that both have four data buses made by pairs of cables with a ground shield. My only work was to put the right cable at the right place!

I have tested successfully simple 5 meter HDMI cables, cheap or expensive cables worked the same. The video signal should not show any degradation until a certain distance (yet to be found).Passed the limit the video signal will be lost entirely. I have not tested HDMI boosters or HDMI conversion to CAT6, please report if you do.

Assembly Instructions

Assembly is simple but require precision to place and tighten the small M2 screws (4mm). To reproduce the setup shown on the first picture:

1 - Assemble the 60mm flat cable between the camera and board, watch carefully the picture for the side of the cable; the connections face away on the extension board and toward the camera.

2 - Lock the connectors in place, here it helps to have long nails. This is mandatory for a good connection.

3 - Place the boards back to back, the flat ribbon should form the shape of an "S".

4 - First with your fingers and maybe tweezers set a screw and spacer loosely. Set another on the opposite side and tighten a bit. Then place the two remaining screws, tighten everything with a small screw driver and a 4mm wrench or a pair of pliers. Et voila you are done!

If after plugging the camera with this kit the Pi does not detect it, you may have bought an HDMI cable without data shield. Please read my blog post that explains an easy fix.

Useful Addition

I made a case for 3D printing (not sold with the kit). The files can be downloaded on Thingiverse. Please post modifications you made.

 

Case Assembly

 

 

 

相關文件

 

 
相關資訊

  *其他套餐*

SD卡請點我進入總覽↓↓↓↓↓↓↓↓↓↓
 
問與答

目前沒有任何商品問答!
本商品上架日期:2017-01-05.
評價
購物車 更多
空的...
查詢訂單狀態
 
請輸入您的訂單編號
商品通知狀態 更多
通知Raspberry Pi Camera HDMI Cable Extension樹莓派 攝像頭轉板 擴充HDMI線(1對2組)
更新時通知我
推薦給朋友
 
推薦這個商品給朋友

聯絡方式:手機:0933807110 或 0968222607
E-mail:i0104@ms13.hinet.net(主要信箱) & i03070309@yahoo.com.tw(次要) & a_te0307@hotmail.com & A9215017@mail.ntust.edu.tw & r94922042@ntu.edu.tw