產品說明1
※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
Sparkfun原廠 FTDI Basic Breakout 模組 5V版本（DEV-09716）mini USB接口
【Description】:
This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same.／這是我們FTDI基礎版的最新版本。我們現在在底部使用 SMD 6 針接頭，使其更小、更緊湊。功能保持不變。
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.／這是FTDI FT232RL USB轉串行IC的基本分線板。該板的引腳排列與FTDI電纜匹配，可與官方Arduino和克隆的5V Arduino板配合使用。它也可用於一般串行應用。與該板的主要區別在於它帶出了DTR引腳，而不是FTDI電纜的RTS引腳。DTR 引腳允許 Arduino 目標在下載新 Sketch 時自動重置。這是一個非常好的功能，無需點擊重置按鈕即可下載草圖。該板將自動重置任何將重置引腳引出到 6 針連接器的 Arduino 板。
The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is CTS. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target.／
標記為 BLK 和 GRN 的引腳對應於 FTDI 電纜上的彩色電線。
FTDI 纜線上的黑線是 GND，綠色是 CTS。
使用這些 BLK 和 GRN 引腳將 FTDI 基本板與您的 Arduino 目標對齊。
This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working.／該板具有 TX 和 RX LED，使其更好地通過 FTDI 電纜使用。您實際上可以在LED上看到串行流量，以驗證電路板是否正常工作。
This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector.／該板旨在降低 Arduino 開發成本並提高易用性（自動重置功能震撼！我們的Arduino Pro板和LilyPad使用這種類型的連接器。
One of the nice features of this board is a jumper on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level). This board ship default to 5V, but you can cut the default trace and add a solder jumper if you need to switch to 3.3V.／該板的一個很好的功能是板背面的跳線，允許將板配置為3.3V或5V（功率輸出和IO電平）。該板出廠預設為 5V，但如果需要切換到 3.3V，您可以切斷預設走線並添加焊接跳線。
Note: We know a lot of you prefer microUSB over miniUSB. Never fear, we've got you covered! Check out our FT231X Breakout for your micro FTDI needs!／注意：我們知道你們中的很多人更喜歡microUSB，而不是miniUSB。別擔心，我們為您提供保障！查看我們的FT231X突破，滿足您的微型FTDI需求！
