※本產品原廠代理從國外進口，有些交期較長，下訂前請詢問！
DEV-18387 升級換：DEV-21869
Sparkfun原廠 MyoWare 2.0 LED Shield（升級DEV-21869）肌肉配件：LED 模組 Type-C
The MyoWare® 2.0 LED Shield is designed to display the magnitude of a target muscle's signal and power the MyoWare 2.0 Muscle Sensor remotely.
影片：https://youtu.be/d1oUHqPa35I
The MyoWare® 2.0 LED Shield is designed to display the magnitude of a target muscle's signal and power the MyoWare 2.0 Muscle Sensor with its built-in battery. The blue 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board LEDs will go! With this shield, you will be provided with a visual representation of the signals provided by the MyoWare 2.0 Muscle Sensor. The LED shield is equipped with snap connectors on the board so you can easily stack it on the top side of the MyoWare 2.0 Muscle Sensor and flip the switch to the ON position to give the sensor all the power it needs to work its myoelectric magic.
MyoWare® 2.0 LED 護罩旨在顯示目標肌肉信號的大小，並通過內置電池為 MyoWare 2.0 肌肉傳感器供電。 藍色的 10 段條形圖顯示了測量信號的幅度。 測量的肌肉激活越多，電路板 LED 就越高！ 使用此防護罩，您將獲得由 MyoWare 2.0 肌肉傳感器提供的信號的可視化表示。 LED 護罩在板上配備了卡扣連接器，因此您可以輕鬆地將其堆疊在 MyoWare 2.0 肌肉傳感器的頂部，並將開關撥至 ON 位置，為傳感器提供發揮其肌電魔力所需的全部功率。
Each board comes with a 40mAh single cell, lithium polymer (LiPo) battery soldered to the board. Recharge the battery through the USB Type C connector and its dedicated LiPo charging circuit is set to a charge rate of 40mA. This board also includes status LEDs for charging (CHG, FULL, and power (VIN)). Connecting the MyoWare 2.0 Muscle Sensor to battery power allows for a cleaner signal while also eliminating the possibility of creating a dangerous current path to the power grid. Use it to gauge how hard you’re working a muscle during a workout, as a teaching tool, or add some myoelectric flair to your Halloween costume!
每個電路板都配備一塊焊接在電路板上的 40mAh 單節鋰聚合物 (LiPo) 電池。可透過 USB Type-C 介面為電池充電，其專用的 LiPo 充電電路設定充電電流為 40mA。此電路板還包含充電狀態指示燈（CHG、FULL 和電源 (VIN)）。將 MyoWare 2.0 肌肉感測器連接到電池電源，可以獲得更純淨的訊號，同時避免形成危險的電流路徑進入電網。您可以將其用於測量運動時肌肉的用力程度，作為教學工具，或為您的萬聖節裝扮增添一些肌電元素！
Note: This item may take longer to process due to battery installed in the equipment and therefore does not qualify for same-day shipping policy. Additionally, these batteries can not be shipped via Ground or Economy methods to Alaska or Hawaii. Sorry for any inconvenience this may cause.
MyoWare and the LED Shield are not intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation treatment, or prevention of disease, in a man or other animals.
［注意］： 由於設備內裝有電池，此商品的處理時間可能會較長，因此不適用當日出貨政策。此外，這些電池無法透過陸運或經濟運輸方式運往阿拉斯加或夏威夷。由此造成的不便，敬請諒解。
MyoWare 和 LED Shield 不適用於診斷人類或其他動物的疾病或其他狀況，或用於治愈、緩解治療或預防疾病。
The MyoWare® 2.0 ecosystem consists of shields that easily interface with the MyoWare® 2.0 Muscle Sensor, which is a low-cost, Arduino-compatible, all-in-one electromyography (EMG) sensor from Advancer Technologies. The innovative connector system allows users to easily snap shields together with a compact low profile and connect to a microcontroller's analog input to measure raw, filtered, and rectified electrical activity of a target muscle. This eliminates the need to solder connections between boards.
MyoWare® 2.0 生態系統由可輕鬆與 MyoWare® 2.0 肌肉傳感器接口的防護板組成，這是一款來自 Advancer Technologies 的低成本、與 Arduino 兼容的一體化肌電圖 (EMG) 傳感器。創新的連接器系統使用戶可以輕鬆地將防護罩與緊湊的薄型連接在一起，並連接到微控制器的模擬輸入，以測量目標肌肉的原始、濾波和整流電活動。這消除了在板之間焊接連接的需要。
This product is a collaboration with Brian Kaminski from Advancer Technologies. A portion of each sales goes back to them for product support and continued development.
該產品是與 Advancer Technologies 的 Brian Kaminski 合作推出的。每次銷售的一部分都會返回給他們，以獲得產品支持和持續開發。
【FEATURES 】：
- Input Voltage
- 5V via USB Type C Connector
- Output Voltage (e.g. "VIN")
- Nominal Voltage： 3.7V
- Fully Charged： 4.2V
- Power Switch
- Built-in LiPo Battery
- Rated Capacity： 40mAh
- Nominal Voltage： 3.7V
- Max Charge Current： 1C (40mA)
- MCP73831 Single Cell LiPo Charge IC
- MyoWare® 2.0 Muscle Sensor Form Factor
- 3x Female Snap Pins (Power and EMG Envelope Output)
- LEDs
- VIN
- FULL
- CHG
- 2x 5-Segment Bars
- Board Dimensions
- 46.15mm x 38.00mm (1.82” x 1.50”)
＊【Revision Changes】： This revision of the MyoWare 2.0 LED Shield includes a 2-pin, 1.00mm pitch JST-SH connector.
＊＊版本變更：此版本的 MyoWare 2.0 LED Shield 包含一個 2 針、1.00mm 間距的 JST-SH 連接器。
